Drive Shafts
 

DANA Industrial Drive Shafts Catalogue

Installation and maintenance
tt  back to Table of contents
Flange boltings
 The flange bolting set can be supplied by DANA on request.

The bolt length given in the tables are only suitable if the dimension 2 x G corresponding to the double the flange thickness G is not exceeded (see data sheets). If longer bolts are used, check whether the bolts can still be inserted from the joint side.

We recommended a bolting set consisting of:
Hexagon bolt with short threat similar to DIN 931/10.9
(shaft length greater than flange thickness)
Self-locking nut, similar to DIN 980/934-10.

The bolts allow fitting
a) partially from the joint side, i.e. the recessed diameter c does not
prevent the bolt from turning;
b) from the companion flange side. We recommend designing the
recessed diameter c1 as locate the bolt head.

See tables for insertion of bolts.
All bolts must be tightened with the specified torque. The tightening torques Ta given in the table are based on a 90% (80% hirth-serration) utilization of the elastic limit and apply to slightly oiled bolts.

Do not use molycote paste or any other grease on the bolts and nuts. In cases of corrosion protected bolts and nuts (eg. Dacromet 500). Please contact us.

Max. permissible tolerance of DIN 25202 class B.

Series 587





Joint flange

Hexagon bolt:
short model
similar to DIN 931/10.9
Hexagon nut:
similar to DIN 980/10
Self-locking
Shaft size 587.50 587.55 587.60
Flange-Ф mm 225 250 250 285 285
Ta Nm 295 405 405 580 580
c mm 158 176 168 202 202
c1 mm 171 189 189 214 214
d - M 16 M 18 M 18 M 20 M 20
l mm 50 60 60 64 64
v mm 20 24 24 24 24
s mm 24 27 27 30 30
i 1) - 8 8 8 8 8
Bolts inserted
from joint side		   yes yes yes yes yes
1) = Number of bolt holes
Ta = Tightening torque of bolting (Special torque wrenches supplied on request)



Series 687





Joint flange

Hexagon bolt:
short model
similar to DIN 931/10.9
Hexagon nut:
similar to DIN 980/10
Self-locking
Shaft size 687.15 687.20 687.25 687.30 687.35 687.40 687.45 687.55 687.65
Flange-Ф mm 100 120 120 120 150 150 180 150 180 180 225 180 225 180 225
Ta Nm 35 69 69 69 120 120 190 120 190 190 295 295 295 295 295
c mm 64 76 76 76 100 100 119 100 119 119 158 118 158 118 158
c1 mm 69,5 84 84 84 110,3 110,3 132,5 110,3 132,5 132,5 171 130,5 171 130,5 171
d - M 8 M 10 M 10 M 10 M 12 M 12 M 14 M 12 M 14 M 14 M 16 M 16 M 16 M 16 M 16
l mm 23 27 27 27 33 33 40 33 40 40 50 50 50 50 50
v mm 9 11 11 11 13 13 16 13 16 16 20 22 20 20 20
s mm 13 17 17 17 19 19 22 19 22 22 24 24 24 24 24
i 1) - 6 8 8 8 8 8 8 8 8 8 8 10 8 10 8
Bolts inserted
from joint
side		 β = 24° yes yes yes yes yes yes yes yes yes yes yes yes yes no yes
β = 35° - - - - - - - yes yes yes - yes - - -
1) = Number of bolt holes
Ta = Tightening torque of bolting (Special torque wrenches supplied on request)



Series 390
Standard bolting





Joint flange

Hexagon bolt:
short model
similar to DIN 931/10.9
Hexagon nut:
similar to DIN 980/10
Self-locking
Shaft size 390.60 390.65 390.70 390.75 390.80
Flange-Ф mm 285 315 350 390 435
Ta Nm 580 780 780 1000 1500
c mm 202 230 256 295 332
c1   mm 214 247 277 308 343
d - M 20 M 22 M 22 M 24 M 27
l mm 64 70 75 85 95
v mm 30 31 30 34 36
s mm 30 32 32 36 41
i 1) - 8 8 10 10 10
Bolts inserted from joint side yes yes yes yes yes
1) = Number of bolt holes
Ta = Tightening torque of bolting (Special torque wrenches supplied on request)



Series 587 / 390
Dowel pin connection





Joint flange

Hexagon bolt:
short model
similar to DIN 931/8.8
Hexagon nut:
similar to DIN 980/10
Self-locking
Dowel pin: DIN 1481
Washer: DIN 7349
Shaft size 587.50 587.55 390.60 390.65 390.70 390.75 390.80
Flange-Ф mm 250 250 285 315 350 390 435
Ta Nm 130 130 200 200 280 280 400
c mm 176 168 202 230 256 295 332
c1 2) mm 176 176 198 228 254 294 332
d - M 14 M 14 M 16 M 16 M 18 M 18 M 20
l mm 65 65 75 75 90 95 110
ds mm 25 25 28 30 32 32 35
ls mm 32 32 36 40 45 50 60
v mm 17 17 23 19 24 23 30
a mm 6 6 6 6 8 8 8
s mm 22 22 24 24 27 27 30
i 1) - 4 4 4 4 4 4 4
Bolts inserted from joint size yes yes yes yes yes yes yes
1) = Number of bolt holes
2) = Dowel pin connection without locking 
Ta = Tightening torque of bolting (Special torque wrenches supplied on request)



Series 587 / 190
Super short design





Joint flange

Hexagon bolt:
short model
similar to DIN 931/10.9
Hexagon nut:
similar to DIN 980/10
Self-locking
Shaft size 587.50 190.55 190.60 190.65 190.70
Flange-Ф mm 275 305 348 360 405
Ta Nm 190 295 405 405 580
c mm 213,5 237,5 274 288 324,5
c1 mm 225 250 285 299 338
d - M 14 M 16 M 18 M 18 M 20
l mm 45 50 60 60 65
v mm 15 20 24 24 21
s mm 22 24 27 27 30
i 1) - 10 10 10 10 10
Bolts inserted from joint side yes yes yes yes yes
1) = Number of bolt holes
Ta = Tightening torque of bolting (Special torque wrenches supplied on request)



Series 392 / 393
Flange connection with face key





Joint flange

Hexagon bolt:
short model
similar to DIN 931/10.9
Hexagon nut:
similar to DIN 980/10
Self-locking
Shaft size 392.50 392.55 392.60 392.65 392.70 393.75 393.80 393.85 393.90
Flange-Ф mm 225 250 285 315 350 390 435 480 550
Ta Nm 295 405 580 780 780 1000 1500 2000 2000
c mm 152 170 193 224 254 288 320 350 420
c1 mm 171 190 214 247 277 307 342 377 444
d - M 16 M 18 M 20 M 22 M 22 M 24 M 27 M 30 M 30
l mm 60 75 80 90 100 110 120 130 140
v mm 20 25 26 26 30 30 36 36 40
s mm 24 27 30 32 32 36 41 46 46
i 1) - 8 8 8 10 10 10 16 16 16
Bolts inserted from joint side no no no no no no no no no
1) = Number of bolt holes
Ta = Tightening torque of bolting (Special torque wrenches supplied on request)



Series 492





Joint flange

Hexagon bolt:
short model
similar to DIN 931/10.9
Hexagon nut:
similar to DIN 980/10
Self-locking
Shaft size 492.75 492.80 492.85 492.90
Flange-Ф mm 390 435 480 550
Ta Nm 375 375 525 720
d - M 18 M 18 M 20 M 22
s mm 27 27 30 32
i 1) - 12 16 16 16
Bolts inserted from joint size no no no no
1) = Number of bolt holes
Ta = Tightening torque of bolting (Special torque wrenches supplied on request)



Series 498





Joint flange

Hexagon bolt:
short model
similar to DIN 931/10.9
Hexagon nut:
similar to DIN 980/934-10
Self-locking
Shaft size 498.00 498.05 498.10 498.15 498.20 498.25 498.30 498.35 498.40 498.45 498.50 498.55 498.60
Flange-Ф mm 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200
Ta Nm 900 900 900 1800 1800 3150 3150 3150 5400 5400 5400 8200 8200
d - M 24 M 24 M 24 M 30 M 30 M 36 M 36 M 36 M 42 x 3 M 42 x 3 M 42 x 3 M 48 x 3 M 48 x 3
s mm 36 36 36 46 46 55 55 55 65 65 65 75 75
i 1) - 20 20 24 24 24 24 24 24 20 20 20 20 20
Bolts inserted from joint size no no no no no no no no no no no no no
1) = Number of bolt holes
Ta = Tightening torque of bolting (Special torque wrenches supplied on request)

 
tt  back to Table of contents
 Email : info@landmark-autoparts.com  Websites

  • ++203 4496682

  • ++203 4496683

  • ++203 4487407

  • ++203 4496690